Audio/Sound Analyzer SG-2230A
Introduction:
This signal analyzing equipment enables us to conduct a simultaneous measurement for frequency response generated from loudspeaker, SPL, Impedance, Fo, Ze, THD, Phase, polarity and C-MIC. It provides product inspection with optimum environment as frequency characteristics and sensitivity of built-in C-Microphone are controlled.
It provides easy maintenance since the product can be installed in all types of computer system with PCI slots. All measuring items can be controlled by setting the criteria for Pass or Fail.
Special Feature:
1. A simultaneous measurement of Frequency Response(SPL), Impedance, Fo, Ze, THD, Phase, and
Polarity provides fast results.
2. High performance SNR>90dB.
3. Sampling rate up to 96kHz
4. Auto Calibration : Microphone.
Manual Calibration : Output voltage.
5. Pass, Fail settings and controls enabled.
6. SPL Balance : SPL level deviation from Left and Right of stereo product can be controlled.
THD Method : Harmonics method can be selected to either IEEC or IEC.
7. Computer-controlled operation Fast, hot plug USB interface.
8. Measurement data is recorded as a file and the Avg, Min, Max, Cp, and Cpk of SPL, Fo, Ze, and THD(4point) can be
calculated (SPC).
9. Can perform remote control through the Internet.
10. Easy document printing in MS Word or Excel file (text format only)
11. Sound Card, MIC Pre-Amp, Conditioning Amp, Power Amp System control.
12. Built-in remote port which enables the connection into automated device.
(Start, Pass, Fail, Test Run)
13. Two input/output ports offer one-time inspection for stereo product. Separate input/output port for C-MIC inspection enables the product inspection with built-in microphone.
Specification:
Sweep Analyzer Level Flatness
50Hz – 20kHz <± 0.1 dB.
20Hz – 20kHz <± 0.3 dB.
15Hz – 20kHz <± 0.5 dB.
Sweep
Log : 1/1,1/3,1/6,1/12,1/24,1/48 Octave steps.
Lin : 1 to 2000 steps.
Preamp. Input
Via standard LEMO 7-Pin Connector
Input Impedance : 1 MΩ/100pF
Input Gain : -20 to 60 ± 0.2dB in steps of 20 ± 0.1dB.
Polarization Voltage : 200V
Power supply : ±15V
Power Amp
Output : 10mv – 10.00v RMS.
Max power : 8W - at 8 ohms
Standard software Sound Production software
(Windows® XP, Vista, W7)
Pentium®4, 1.5GHz processor minimum or equivalent.
(Celeron processors are not recommended)
Interface Bus Personal computer connected to the instrument
through the Sound Analyzer Interface Bus. (USB2.0)
Sound Card = 1 PCI Slot
Remote control interfaces 9P D-Type connector I/O signal - Start, Pass, Fail, Test_Run
through the Sound Analyzer Interface Bus. (USB2.0)
Power Requirements : AC 220V 50/60Hz 90VA
Dimensions : 300(W) × 115(H) × 255(D) mm
Weight : Approx. 3Kg
Display:
Detailed specification sheets are shown in the product images.
Audio/Sound Analyzer SG-2230A
Audio/Sound Analyzer SG-2230A: overview and buying guide
The Audio/Sound Analyzer SG-2230A (model SG-2230A) is made by Sigma Eltec and listed in our test · measurement range. Premium Emart sources it directly from the manufacturer and handles the quotation, inspection, export packing and international shipping, so you can buy it from anywhere in the world with a single point of contact.
Frequently asked questions
How much does the Audio/Sound Analyzer SG-2230A cost?
Prices depend on the configuration, quantity and destination. Add the item to your RFQ list and we will send a free quotation with the unit price, lead time and shipping cost. There is no obligation to buy.
Can you ship the Audio/Sound Analyzer SG-2230A to my country?
Yes. We export worldwide by sea, air or courier, with export packing and the commercial invoice, packing list and certificate of origin where required. The shipping options are shown in your quotation.
Is this a genuine Sigma Eltec product?
We purchase directly from Sigma Eltec or its authorised channels and confirm the model and specifications with the manufacturer before ordering.
What is the minimum order quantity?
For most items the minimum order is one unit. If the manufacturer sets a higher minimum, we tell you in the quotation.
Introduction:
This signal analyzing equipment enables us to conduct a simultaneous measurement for frequency response generated from loudspeaker, SPL, Impedance, Fo, Ze, THD, Phase, polarity and C-MIC. It provides product inspection with optimum environment as frequency characteristics and sensitivity of built-in C-Microphone are controlled.
It provides easy maintenance since the product can be installed in all types of computer system with PCI slots. All measuring items can be controlled by setting the criteria for Pass or Fail.
Special Feature:
1. A simultaneous measurement of Frequency Response(SPL), Impedance, Fo, Ze, THD, Phase, and
Polarity provides fast results.
2. High performance SNR>90dB.
3. Sampling rate up to 96kHz
4. Auto Calibration : Microphone.
Manual Calibration : Output voltage.
5. Pass, Fail settings and controls enabled.
6. SPL Balance : SPL level deviation from Left and Right of stereo product can be controlled.
THD Method : Harmonics method can be selected to either IEEC or IEC.
7. Computer-controlled operation Fast, hot plug USB interface.
8. Measurement data is recorded as a file and the Avg, Min, Max, Cp, and Cpk of SPL, Fo, Ze, and THD(4point) can be
calculated (SPC).
9. Can perform remote control through the Internet.
10. Easy document printing in MS Word or Excel file (text format only)
11. Sound Card, MIC Pre-Amp, Conditioning Amp, Power Amp System control.
12. Built-in remote port which enables the connection into automated device.
(Start, Pass, Fail, Test Run)
13. Two input/output ports offer one-time inspection for stereo product. Separate input/output port for C-MIC inspection enables the product inspection with built-in microphone.
Specification:
Sweep Analyzer Level Flatness
50Hz – 20kHz <± 0.1 dB.
20Hz – 20kHz <± 0.3 dB.
15Hz – 20kHz <± 0.5 dB.
Sweep
Log : 1/1,1/3,1/6,1/12,1/24,1/48 Octave steps.
Lin : 1 to 2000 steps.
Preamp. Input
Via standard LEMO 7-Pin Connector
Input Impedance : 1 MΩ/100pF
Input Gain : -20 to 60 ± 0.2dB in steps of 20 ± 0.1dB.
Polarization Voltage : 200V
Power supply : ±15V
Power Amp
Output : 10mv – 10.00v RMS.
Max power : 8W - at 8 ohms
Standard software Sound Production software
(Windows® XP, Vista, W7)
Pentium®4, 1.5GHz processor minimum or equivalent.
(Celeron processors are not recommended)
Interface Bus Personal computer connected to the instrument
through the Sound Analyzer Interface Bus. (USB2.0)
Sound Card = 1 PCI Slot
Remote control interfaces 9P D-Type connector I/O signal - Start, Pass, Fail, Test_Run
through the Sound Analyzer Interface Bus. (USB2.0)
Power Requirements : AC 220V 50/60Hz 90VA
Dimensions : 300(W) × 115(H) × 255(D) mm
Weight : Approx. 3Kg
Display:
Detailed specification sheets are shown in the product images.



