Home / Blog

Vibration Analysis and Predictive Maintenance Explained

Product Guides · 21 November 2026 · 4 min read
Test and measurement instruments – illustrative image

Most rotating machines give warning signs long before they fail. A bearing starts to wear, a coupling drifts out of alignment or a fan accumulates dirt on one side, and the machine begins to vibrate in a characteristic way. Vibration analysis is the practice of measuring and interpreting that vibration to detect developing faults early. It is the foundation of predictive maintenance, an approach in which repairs are planned based on the actual condition of equipment rather than waiting for breakdowns or replacing parts on a fixed schedule. This guide explains what vibration reveals, the tools used to measure it and how to start a simple, effective predictive maintenance programme.

Three approaches to maintenance

It helps to compare predictive maintenance with the alternatives. Reactive maintenance means running equipment until it fails and then repairing it. It is simple but leads to unplanned downtime, secondary damage and emergency costs. Preventive maintenance means servicing or replacing parts at fixed intervals. It reduces breakdowns but often replaces parts that still have plenty of life left, and it does not catch failures that happen between intervals. Predictive maintenance monitors the condition of equipment and acts only when measurements show that a problem is developing. It combines the reliability of preventive maintenance with lower cost and less unnecessary work.

What vibration reveals

Every rotating machine vibrates to some extent. What matters is how the vibration changes and at which frequencies it occurs. Different faults produce different patterns:

  • Imbalance – uneven mass distribution, for example from dirt build-up on a fan, produces vibration at the running speed, mainly in the radial direction.
  • Misalignment – shafts that are not correctly aligned produce vibration often at twice the running speed and significant axial vibration.
  • Mechanical looseness – loose bolts, cracked foundations or worn fits produce many harmonics of the running speed.
  • Rolling bearing defects – damage to the races, rolling elements or cage produces characteristic high-frequency patterns at defect frequencies that can be calculated from the bearing geometry.
  • Gear faults – worn or damaged teeth produce activity at the gear mesh frequency and its sidebands.
  • Electrical faults in motors – such as rotor bar problems or uneven air gaps, which produce specific frequency patterns related to the supply frequency.
  • Resonance – when a running speed coincides with a natural frequency of the structure, vibration is amplified dramatically.

How vibration is measured

Vibration is usually measured with an accelerometer, a sensor that converts motion into an electrical signal. It is mounted on the bearing housing, as close as possible to the bearing, using a magnet, a stud or an adhesive pad. Measurements can be expressed as displacement, velocity or acceleration. Velocity is commonly used for overall machine condition, while acceleration and special processing techniques such as enveloping or demodulation are used to detect early bearing damage. Analysers convert the time signal into a frequency spectrum using a mathematical technique called the Fast Fourier Transform, which shows how much vibration occurs at each frequency and allows faults to be identified.

Tools for the job

  • Handheld vibration meters give a quick overall reading and often a simple bearing condition indicator. They are inexpensive and ideal for starting a programme.
  • Data collectors and analysers record full spectra and time waveforms on a route of machines, which are then downloaded to software for trending and diagnosis.
  • Permanently mounted sensors connected to monitoring systems continuously monitor critical machines and can trigger alarms or shut down equipment.
  • Wireless sensors are increasingly popular because they are easy to install on many machines and send data automatically to a central system or cloud platform.

Severity guidelines

International standards, notably the ISO 20816 series, provide guidance on acceptable vibration levels for different classes of machines, based on size, type and mounting. These levels are useful as a starting point, but the most valuable information usually comes from trends: a machine whose vibration doubles over a few weeks needs attention even if the absolute level is still within guidelines.

Starting a predictive maintenance programme

  1. Identify critical machines. Start with equipment whose failure stops production, is expensive to repair or creates safety risks, such as main pumps, compressors, fans, gearboxes and spindles.
  2. Define measurement points. Mark fixed points on each bearing housing in the horizontal, vertical and axial directions, so readings are always taken in the same place.
  3. Record baseline readings. Measure when machines are in good condition, ideally after commissioning or a major overhaul.
  4. Set a schedule. Measure at regular intervals, often monthly for critical machines, and more frequently when a problem is developing.
  5. Set alarm levels. Use standards and baseline data to set alert and danger levels for each machine.
  6. Analyse and act. When readings rise, analyse the spectrum to identify the cause and plan the repair at a convenient time, such as a weekend or scheduled shutdown.
  7. Review results. After each repair, inspect the removed parts to confirm the diagnosis, and use what you learn to improve the programme.

Combining techniques

Vibration analysis is powerful, but it works best alongside other condition monitoring techniques. Infrared thermography detects hot spots in electrical panels, bearings and motors. Oil analysis reveals wear metals, contamination and lubricant breakdown in gearboxes and hydraulic systems. Ultrasound detects early bearing faults, lubrication problems, compressed air leaks and electrical discharges. Motor current analysis identifies electrical faults in motors. Together, these techniques give a much more complete picture of machine health.

Benefits

A well-run predictive maintenance programme reduces unplanned downtime, prevents secondary damage, extends the life of components, allows spare parts and labour to be planned in advance and improves safety. Many companies find that savings from a single prevented failure of a critical machine pay for the measurement equipment many times over.

Finding instruments and sensors

Explore test and measurement instruments, including vibration meters, accelerometers, analysers and monitoring systems, from Korean and international makers. Replacement bearings and couplings identified through your analysis can be found in our stock list.

Summary

Vibration analysis turns unexpected breakdowns into planned repairs. Start with your most critical machines, measure consistently at fixed points, watch the trends, and act when the data shows a problem is developing. Combined with other condition monitoring techniques, it is one of the most effective ways to improve reliability.

Need a price? Add items to your RFQ list or send a custom sourcing request – quotations are free and there is no obligation.

Need a quote from Korea?

Tell us what you need – our Seoul team collects offers from Korean manufacturers and replies in USD.

Start your RFQ

← All articles